Skip to content
Quantum.world

The Signal

CMOS Titanium Nitride Becomes a Compact Quantum-Dot Sensor

A titanium nitride film in a commercial CMOS process serves as a compact superinductor paired with a silicon quantum dot in a radio-frequency single-electron transistor. The sensor reaches a signal-to-noise ratio of 4,500 in a 4-nanosecond integration time, while the inductor’s nonlinear response could support parametric circuits.

CMOS Titanium Nitride Becomes a Compact Quantum-Dot Sensor

A titanium nitride film already present in a commercial silicon CMOS process can serve as the high-impedance element in an integrated quantum-dot sensor. The Nature Electronics paper describes a superinductor made in GlobalFoundries’ 22-nm fully depleted silicon-on-insulator process, then paired on the same circuit with a silicon quantum dot. The resulting radio-frequency single-electron transistor, or rfSET, is a charge sensor used in semiconductor spin-qubit systems.

TiN turns a CMOS film into a superinductor

The work draws on titanium nitride in the process’s poly-resistor structures. At deep-cryogenic temperatures, the thin film becomes superconducting, and the motion of Cooper pairs contributes kinetic inductance. The authors characterize two film variants, labelled type A and type B, which use different doping profiles in some layers. They measure the films’ voltage-current properties and use a TiN section as the inductive element in a resonator.

The extracted inductance per square is 1.07 nH sq−1 for type A and 0.94 nH sq−1 for type B. The integrated inductor has an area of 18 μm². Its inductance density is 8 nH μm−2 for type A and 7 nH μm−2 for type B, four orders of magnitude higher than the typical spiral-inductor density of 200 nH mm−2 cited in the paper.

To characterize the films, the researchers measure structures with widths from 0.36 to 3.6 μm and lengths from 0.36 to 50 μm. They report critical temperatures of 0.75 K for type A and 1.1 K for type B. In the resonator test, the superconducting film produces a resonance at 884 MHz; the resonance is absent when the film is in its normal state.

A resonator and quantum dot share one circuit

The team connects the TiN-containing resonator to a silicon quantum dot formed in the same integrated circuit. The dot operates as the island of a single-electron transistor, whose source–drain resistance changes with its electrostatic environment. With spin-to-charge conversion, an SET can detect a semiconductor qubit’s spin state from a single charge-tunnelling event.

Embedding an SET in an LC matching network lets the circuit transform its high source–drain impedance to the 50-Ω impedance of a transmission line. The paper identifies the size of conventional inductors as a constraint on scaling spin-based quantum computers, and uses the compact TiN element in the rfSET sensor. The sensor achieves a signal-to-noise ratio of 4,500 in a 4-ns integration time. The authors calculate that an integration time of 1 ± 0.3 ps would produce a signal-to-noise ratio of 1, an improvement of more than two orders of magnitude compared with previous systems.

Nonlinearity adds a second function

The sensor’s sensitivity is boosted by the TiN superinductor’s nonlinear kinetic inductance. The authors develop a theoretical model that gives a steep cubic scaling of signal-to-noise ratio with incident power, in agreement with their experimental observations. The current-dependent inductance also allows the possibility of parametric amplification through three-wave or four-wave mixing.

The films show resilience to in-plane magnetic fields up to 2 T, which the paper says makes them compatible with spin qubits. The maximum impedance is calculated as 11.5 kΩ using the maximum measured inductance of 807 nH and the inductor’s parasitic capacitance; it exceeds the superconducting resistance quantum of about 6.45 kΩ.

“Our approach could lead to the development of parametric circuits, kinetic-inductance detectors and quantum simulators based on one-dimensional and two-dimensional resonator arrays using integrated circuits.”

The authors write that sentence in describing possible applications of superconducting inductors made with commercial CMOS processes. Their work combines the integrated inductor with a quantum dot in one sensor circuit, while showing how the TiN film’s nonlinear response can contribute to the circuit’s performance.

Source

  1. Nature Electronics

Related stories

Explore

More articles